OSHA Top Ten Citation Categories 2016

From the OSHA Blog:

Labor’s Occupational Safety and Health Administration releases a preliminary list of the 10 most frequently cited safety and health violations for the fiscal year, compiled from nearly 32,000 inspections of workplaces by federal OSHA staff. One remarkable thing about the list is that it rarely changes.

Year after year, our inspectors see thousands of the same on-the-job hazards, any one of which could result in a fatality or severe injury. More than 4,500 workers are killed on the job every year, and approximately 3 million are injured, despite the fact that by law, employers are responsible for providing safe and healthful workplaces for their workers. If all employers simply corrected the top 10 hazards, we are confident the number of deaths, amputations and hospitalizations would drastically decline. Consider this list a starting point for workplace safety:

  1. Fall protection
  2. Hazard communication
  3. Scaffolds
  4. Respiratory protection
  5. Lockout/tagout
  6. Powered industrial trucks
  7. Ladders
  8. Machine guarding
  9. Electrical wiring
  10. Electrical, general requirements

It’s no coincidence that falls are among the leading causes of worker deaths, particularly in construction, and our top 10 list features lack of fall protection as well as ladder and scaffold safety issues. We know how to protect workers from falls, and have an ongoing campaign to inform employers and workers about these measures. Employers must take these issues seriously. We also see far too many workers killed or gruesomely injured when machinery starts up suddenly while being repaired, or hands and fingers are exposed to moving parts.

Lockout/tagout and machine guarding violations are often the culprit here. Proper lockout/tagout procedures ensure that machines are powered off and can’t be turned on while someone is working on them. And installing guards to keep hands, feet and other appendages away from moving machinery prevents amputations and worse.

Respiratory protection is essential for preventing long term and sometimes fatal health problems associated with breathing in asbestos, silica or a host of other toxic substances. But we can see from our list of violations that not nearly enough employers are providing this needed protection and training.

The high number of fatalities associated with forklifts, and high number of violations for powered industrial truck safety, tell us that many workers are not being properly trained to safely drive these kinds of potentially hazardous equipment.

Rounding out the top 10 list are violations related to electrical safety, an area where the dangers are well-known. Our list of top violations is far from comprehensive. OSHA regulations cover a wide range of hazards, all of which imperil worker health and safety. And we urge employers to go beyond the minimal requirements to create a culture of safety at work, which has been shown to reduce costs, raise productivity and improve morale.

To help them, we have released new recommendations for creating a safety and health program at their workplaces. We have many additional resources, including a wealth of information on our website and our free and confidential On-site Consultation Program. But tackling the most common hazards is a good place to start saving workers’ lives and limbs.

All Lift Service Co is your source for reliable and credible Forklift Operator Safety Training. Visit our website to learn more then contact us at 877-303-LIFT for more information or to schedule training.

Advertisements

Section 179 is Back and Better for 2016

Sec179Congress has approved much needed improvements in Section 179 which allows companies, like yours, the ability to completely deduct the purchase cost of equipment the first year it is put into service. The new limits are:

Maximum 179 Deduction for 2016: $500,000

This means for qualifying equipment purchases of up to $500,000, your company can deduct 100% of the purchase price from its taxes the very first year it is put into service.

Further, this maximum will be increased annually, with the maximum tied to inflation, at $10,000 increments.

Bonus Depreciation; Maximum Qualifying Purchases: $2,000,000

Once you exceed the maximum deduction of $500,000, bonus depreciation kicks in at 50%, until you reach the maximum qualifying purchases of $2,000,000. For example, if you spend $1,000, ooo on new equipment, you can fully deduct the first $500,000, then deduct 50% of the remaining $500,000 for a total tax deduction the first year of $750,000.  It then begins to phase out dollar for dollar until you reach $2,500,000, where it is then completely eliminated.

Bonus Depreciation will be extended through 2019. Businesses of all sizes will be able to depreciate 50 percent of the cost of equipment acquired and put in service during 2015, 2016 and 2017. Then bonus depreciation will phase down to 40 percent in 2018 and 30 percent in 2019.

Note: The section 179 deduction applies to NEW and USED equipment whereas the bonus depreciation is only available for NEW equipment.

What that means to the purchase price of a NEW, $30,000 forklift? Assuming your company is in the 35% tax bracket, your effective cost, after deducting the entire $30,000 from your taxes, is only $19,500!

With Section 179 in effect for the remainder of 2015 and all of 2016, and beyond, there’s never been a better time to invest in new forklifts for your facility.

Note: We always suggest you consult your accountant or tax professional before you utilize section 179 for tax savings. Not all companies are structured the same and your savings may vary.

To learn more about Section 179, please visit; www.section179.org. Visit our New CLARK Forklifts showroom, our New KOMATSU Forklifts showroom to see our models. Then Contact Us for a quote, or give us a call at 877-303-LIFT.

When is Forklift Operator Safety Training Required, and Recommended

By now we all know that anyone that operates lift trucks in your facility MUST be trained to do so. This training needs to be done on YOUR type of equipment, operated in YOUR facility. But when does and operator need to be “refreshed” on forklift operator training, and why? OSHA States:

1910.178(l)(4)(i) – Refresher training, including an evaluation of the effectiveness of that training, shall be conducted as required by paragraph (l)(4)(ii) to ensure that the operator has the knowledge and skills needed to operate the powered industrial truck safely.
1910.178(l)(4)(ii) – Refresher training in relevant topics shall be provided to the operator when:
1910.178(l)(4)(ii)(A) – The operator has been observed to operate the vehicle in an unsafe manner;
1910.178(l)(4)(ii)(B) – The operator has been involved in an accident or near-miss incident;
1910.178(l)(4)(ii)(C) – The operator has received an evaluation that reveals that the operator is not operating the truck safely;
1910.178(l)(4)(ii)(D) – The operator is assigned to drive a different type of truck; or
1910.178(l)(4)(ii)(E) – A condition in the workplace changes in a manner that could affect safe operation of the truck.
1910.178(l)(4)(iii) – An evaluation of each powered industrial truck operator’s performance shall be conducted at least once every three years.

This means that when you hire a new forklift operator, or someone that might operate a forklift for any reason in your facility, you need to find out what type of equipment they have been trained to operate, how and under what conditions. If your new employee previously operated electric order pickers in a distribution setting and your operation utilizes IC forklifts used outdoors, your new employee will need refresher training using your type of equipment under your conditions. This condition would apply under sections D and E as outlined above.

This could also be said for a current employee transferring from another facility that uses different types of attachments or moves different kinds of products. You would need to provide hands-on training and evaluation for your equipment, how to use it, what it does to capacity rating and how to safety maneuver your goods around your facility.

A new employee may have had training at a previous job, using similar equipment under similar conditions. If however, you as a supervisor determine that the new employee is not exhibiting sufficient knowledge of forklift safety, complete training may be an order. OSHA doesn’t address every situation and condition in it’s standard 1910.178, but it is up to us to carefully evaluate our operators on a regular basis and determine if we think refresher training is needed, or if an employee needs to undergo complete training.

Our goal is to help you achieve the safest and most productive workplace in Northeast Ohio. if you feel you could use a partner in Forklift Operator Training, please Contact Us, or give us a call at 877-303-LIFT.